Kreg Tool KHC-MICRO Classic 2" Face Clamp is a compact clamping tool made for holding parts flush during assembly. This is a face clamp designed for creating flush joints during pocket-hole assembly. Model Number: KHC-MICRO. If you build cabinets, small furniture, face frames, or general woodworking projects with pocket-hole joinery, this clamp gives you better control over alignment before the screw ever goes in.

The big deal here is how the clamp applies pressure. The large clamp pads spread force across the work instead of digging into one small point, which helps hold pieces flush without marring the surface. That matters when you are working on visible faces or finished stock where cleanup time turns into wasted time. The 2 inch reach and capacity for materials up to 2-1/4 inches thick give it enough range for a lot of common shop assemblies while keeping the tool compact.

Compared to a bulkier clamp, this smaller format is easier to use in tight spaces and around smaller parts. That is especially helpful when you are assembling narrow rails, edge joints, or components where a larger clamp frame gets in the way. The simple screw adjustment lets you dial the clamp to material thickness, then lock and release it quickly as you move through repeat work.

Kreg designed this clamp specifically with pocket-hole work in mind, and that shows in the pad layout. The extra-large clamp face is intended to sit on the show side of the joint, helping keep the visible side flat while the backside gets the fastener. In practical use, that means less chance of one board creeping proud of the other while you drive the screw.

From a build standpoint, the Kreg Tool KHC-MICRO Classic 2" Face Clamp uses a steel body with a padded ergonomic grip. The steel construction gives it the rigidity you want in a clamp, while the handle makes it more comfortable during repeated open-close cycles. It is the kind of hand tool that earns its keep in a small shop because it is quick to grab, easy to set, and useful far beyond one single jig setup.

Compatibility is another reason this clamp matters if you already work in the Kreg system. It is compatible with the Kreg Pocket-Hole Jig R3 Portable Clamp Adapter and 300-Series Pocket-Hole Jigs. That gives it a clear place in a Kreg joinery workflow instead of being just another general-purpose clamp hanging on the wall.

Who should buy it? Woodworkers, cabinet installers, trim carpenters, and serious DIY users who want better alignment during pocket-hole fastening. If you mainly build smaller assemblies or work in tighter spaces, this smaller Kreg face clamp makes more sense than jumping straight to a larger model. If your work regularly involves wider stock or bigger panel assemblies, you may still want a larger companion clamp, but for compact joinery work this one is a smart pickup.

Why the Kreg Tool KHC-MICRO Classic 2" Face Clamp Belongs on a Pocket-Hole Bench

This is the kind of small, purpose-built clamp that saves a surprising amount of hassle when you want pocket-hole joints to come together clean and flush.

• Who it's for: Woodworkers, cabinet builders, and serious DIY users doing face frames, small assemblies, and general pocket-hole fastening.
• Why it stands out: The compact size is actually useful, not just smaller. It gets into tighter work, holds faces even, and plays nicely with Kreg jig setups.
• Worth knowing: This is the MICRO version, so it is best when space is tight or parts are smaller. If you regularly clamp larger stock, pair it with a bigger face clamp instead of asking one tool to do every job.

• What is this clamp mainly used for? It is mainly used to hold parts flush during pocket-hole assembly, though it also works for other woodworking tasks that need non-marring clamping.
• How much material can it clamp? The listed maximum material capacity is up to 2-1/4 inches thick.
• Is it compatible with Kreg pocket-hole jigs? Yes. It is compatible with the Kreg Pocket-Hole Jig R3 Portable Clamp Adapter and Kreg 300-Series Pocket-Hole Jigs.
• What makes it different from a standard clamp? The large face pads are designed to spread pressure and keep joint faces aligned, which is especially useful when assembling pocket-hole joints.