Makita 9/16-in. x 12-in. Hollow Socket (B-43315)
Makita 9/16-in. x 12-in. Hollow Socket (B-43315)
In Stock - Ready to Ship
Product Details
Product Details
Key Features
Overview
The Makita B-43315 9/16 in. x 12 in. Hollow Socket is a deep hollow socket made for running nuts over long threaded rod, studs, and extra-long bolts. This is a hollow socket designed for overhead fastening applications. Model Number: B-43315. If you do HVAC, electrical, strut work, or any install where you're spinning nuts high above your head, this tool cuts down the slow part of the job.
The main advantage here is simple: the hollow shaft allows threaded rod to pass through the middle of the socket instead of bottoming out. That means you can keep driving the nut without stopping to reposition. On jobs with long hanger rod, pipe supports, ceiling grid supports, or duct mounting hardware, that saves real time and a lot of finger work.
Makita built this socket with a 1/4 inch hex shank, so it works directly with both impact drivers and drill-drivers. The shank is axial press-fit, which Makita calls out for better durability and torsional strength than a one-piece hollow socket design. In plain terms, it is built to handle repeated fastening without feeling like a disposable accessory.
The 9/16 inch socket size and 12-point design matter too. The 12-point opening gives easier fitment over both 6-point and 12-point fasteners, which helps when you are working overhead and do not want to waste time lining up the socket. The extra length also gives better access to nuts located in tight spots around ceiling assemblies, ductwork, and pipe runs.
Makita also includes a smooth, chamfered inner well to help prevent the shaft from biting into threads during fastening and unfastening. That is a small detail, but it matters when you are working with threaded rod all day and do not want the tool hanging up or chewing up the threads. The corrosion-resistant finish is there for longer service life, especially for contractors using it regularly on active jobsites.
This is not a general-purpose socket you buy for a drawer full of hand tools. It is a job-specific fastening accessory for people who work with rod and nuts often enough to care about speed, reach, and reduced fatigue. If you only touch threaded rod once in a while, a standard setup may get by. If you do overhead installs every week, the Makita B-43315 9/16 in. x 12 in. Hollow Socket makes a very convincing case for itself.
Reach Nuts in High, Tight Spots
The long body and hollow center are what make this socket useful on the job. It is built to reach nuts that sit deep on threaded rod where a standard socket or nut driver slows you down.
- 12 inch length improves access in ceilings, ductwork, and other hard-to-reach areas
- Hollow shaft passes over extra-long bolts, studs, and threaded rod
- Lightweight design helps reduce wear during overhead use
Key Specifications
| Socket Size | 9/16 in |
|---|---|
| Overall Length | 12 in |
| Drive Size | 1/4 in hex shank |
| Point Configuration | 12-point |
| Socket Depth | Deep |
| Material | Steel |
| Measurement Standard | SAE |
| Weight | 0.3 lbs |
Compatibility
Built For
Warranty & Support
Tool Nut's Take
Makita B-43315 9/16 in. x 12 in. Hollow Socket for Fast Rod Work
This is one of those specialty fastening tools that looks simple until you use it on a ceiling job and realize how much time it saves.
- Who it's for: HVAC techs, electricians, and contractors who regularly run nuts up threaded rod, hangers, or overhead supports.
- Why it stands out: The hollow shaft, 12 inch reach, and impact-driver-ready 1/4 inch hex shank solve a real jobsite problem instead of adding another gimmick to the bag.
- Worth knowing: This is a single 9/16 inch socket, so it is best for crews who already know that size is part of their daily work.
Common Questions
- What kind of tool does this socket work with? It has a 1/4 inch hex shank and works directly with impact drivers and drill-drivers.
- What size fastener is this for? This socket is 9/16 inch.
- Will it fit only 12-point fasteners? No. The 12-point socket design is made for easy fitment over both 6-point and 12-point fasteners.
- Why is the socket hollow? The hollow center allows long bolts, studs, and threaded rod to pass through the socket during fastening.

Join over 1/2 million customers who have trusted Tool Nut and given us a 4.8+ star rating on Google. Celebrating over 30 years of building together, since 1994.
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

