Kreg KFT4X8 4' x 8' Face-Framing Table
Kreg KFT4X8 4' x 8' Face-Framing Table
In Stock - Ships from Manufacturer
Product Details
Product Details
Key Features
Overview
The Kreg KFT4X8 4' x 8' Face-Framing Table (Model Number: KFT4X8) is a face-frame assembly work table built for fast, repeatable clamping and squaring during cabinet face-frame joinery. This is a face-framing assembly table designed for clamping and squaring cabinet face frames during pocket-hole joinery and general frame assembly.
The whole point here is keeping the joint line dead flush while you fasten. The table uses four adjustable clamping cylinders that apply pressure right where rails and stiles meet. Because each cylinder can be positioned and adjusted, you can set it up for a wide range of frame sizes instead of fighting one fixed clamp point.
Unlike a flat assembly bench that eats up floor space and forces you to hunch over, the angled table layout is designed to keep the work comfortable and accessible while taking up less room. That matters if you are assembling face frames all day and want consistent results without wearing your back out.
The retractable squaring fence on the left side is there for one job: start square, every time. Get the first corner registered, then slide the fence out of the way when the frame length exceeds 8 feet so you are not boxed in by the table hardware.
For shop workflow, the clamping system is built for flexibility. The cylinders can be controlled independently, or you can activate them together with the master switch located on the bottom of the clamping arm. That makes it easier to stage parts, confirm alignment, then clamp in one move.
This table is a fit for cabinet shops, millwork, and production woodworking where face frames are a daily task and consistency matters. If you only build the occasional frame, it is more table than you need. If you build frames every week, it is the kind of setup that pays you back in speed and fewer reworks.
Clamp Pressure Where It Counts
Good face frames come down to flush joints. The clamping cylinders are built to hold parts tight at the joint line so your fasteners do not pull things out of plane.
- Four clamping cylinders with adjustable positioning
- Designed to apply pressure on the joint line to maintain a flush assembly
Start Square, Then Get Clearance
The retractable squaring fence helps you get the first corner locked in square, then it pulls back so longer frames are not limited by the fence length.
- Retractable aluminum squaring fence on the left side
- Fence retracts to accommodate frames larger than 8 feet
More Output in Less Floor Space
The angled work surface is built for stand-up assembly, and it is designed to take up less space than a flat table in a production shop layout.
- Uses less floor space than a flat table
- Allows the worker to stand upright during use
Key Specifications
 Overall Height |
76 in |
|---|---|
 Overall Width |
110 in |
 Overall Depth |
30 in |
 Weight |
350 lb |
|
Clamping Cylinders |
4 |
 Product Type |
Work Table (Face-Framing Table) |
Built For
Pro Tip
If you are building a long frame, square the first corner against the fence, clamp it, then retract the fence and keep assembling. You get the squareness benefit without the fence limiting your length.
Tool Nut's Take
Kreg KFT4X8 4' x 8' Face-Framing Table: built for repeatable flush frames
If face frames are a regular part of your output, this table is all about faster clamping, better alignment, and less cleanup.
- Who it's for: Cabinet and woodworking shops doing frequent face-frame assembly and needing consistent, square results.
- Why it stands out: Four adjustable clamping cylinders and a retractable squaring fence that helps you start square, then keep moving on longer frames.
- Worth knowing: This is a dedicated, heavy work table at 350 lb, so plan where it lives in the shop before it shows up.
Common Questions
- How many clamping cylinders does the table have? It uses four adjustable clamping cylinders.
- Can it handle frames longer than 8 feet? Yes. The left-side squaring fence retracts out of the way to accommodate frames larger than 8 feet.
- Can I clamp one station at a time? Yes. Each clamping cylinder can be controlled independently, or all can be activated at once using the master switch on the bottom of the clamping arm.
Join over 1/2 million customers who have trusted Tool Nut and given us a 4.8+ star rating on Google. Celebrating over 30 years of building together, since 1994.
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
