Milwaukee Shockwave 11-Piece 30-Degree Knuckle (48-32-2301)
Milwaukee Shockwave 11-Piece 30-Degree Knuckle (48-32-2301)
In Stock - Ready to Ship
Product Details
Product Details
Key Features
Overview
The Milwaukee 48-32-2301 SHOCKWAVE 30° KNUCKLE Pivoting Bit Holder is a pivoting bit holder set built for impact driving in tight spaces. This is a bit holder designed for fastening and light drilling access where a straight setup will not clear the work. Model Number: 48-32-2301. If you use an impact driver around installed cabinets, electrical boxes, HVAC runs, framing corners, or other cramped spots, this set is made to keep the tool working instead of forcing you back to a hand screwdriver.
The big selling point is the locking pivot. This holder locks at either 0 degrees for straight driving or 30 degrees for offset access. That sounds simple, but on the job it matters. It lets you get onto screws and small fasteners when the body of the driver cannot line up directly behind the bit. For remodel work and service calls, that can save time and a lot of knuckle-busting.
Milwaukee rates the holder to 2,000 inch-pounds of torque, which tells you this is meant for real impact driver use, not just occasional finish work. The 1/4 inch hex Power Groove shank is built to work with quick-connect chucks, and the magnetic tip helps keep the fastener planted while you start it. That combination is especially useful when you are reaching into a corner or driving overhead where dropped screws slow everything down.
The SHOCKWAVE construction matters here too. Milwaukee calls out proprietary steel and a heat-treat process for strength and durability, and that is the right focus for a pivoting accessory. Any angled holder sees extra stress at the joint, so material quality is what separates a holder that stays in rotation from one that gets sloppy or fails early. This one is engineered as an impact-rated accessory, which is exactly what you want if it is going to live in the same bag as your everyday impact driver bits.
This 11-piece set includes the pivoting holder and 10 insert bits in common profiles. That makes it more than just a specialty attachment. It gives you a usable mix for general fastening right away, including Phillips, square, slotted, and Torx options. For a service tech, installer, or punch-list guy, that means one compact set can cover a lot of quick jobs without digging through loose bits.
Compatibility is straightforward. The holder is designed for use with 1/4 inch hex accessories and quick-connect chucks, so it fits the standard setup most impact drivers and bit-ready drills already use. If you are already running Milwaukee SHOCKWAVE Impact Duty accessories, this is built to work within that system, but the 1/4 inch hex interface is the part that matters most in daily use.
Who should buy it? Anyone who regularly runs into access problems while fastening. Electricians, HVAC installers, cabinet installers, maintenance techs, remodelers, and general contractors will get the most out of it. If most of your work is wide-open bench assembly, a standard bit holder may be enough. But if you are constantly trying to reach one screw behind something installed, this angled bit holder earns its spot fast.
Reach Fasteners a Straight Holder Cannot
The reason to buy this set is simple: access. The pivot lets the holder work straight or kicked over to 30 degrees, so you can keep using your driver in places that normally force a slower workaround.
- Locks at 0 degrees or 30 degrees for controlled positioning
- Built for driving fasteners and drilling holes in tight work areas
What's in the Box
- (1) 30° KNUCKLE Pivoting Bit Holder
- (1) Phillips #1 1 inch insert bit
- (4) Phillips #2 1 inch insert bits
- (1) Phillips #3 1 inch insert bit
- (1) Square #1 1 inch insert bit
- (1) Square #2 1 inch insert bit
- (1) Slotted 1/8 inch 1 inch insert bit
- (1) Slotted 3/16 inch 1 inch insert bit
- (1) Slotted 1/4 inch 1 inch insert bit
- (1) Slotted 9/32 inch 1 inch insert bit
- (1) Torx T25 2 inch insert bit
Key Specifications
|
|
11 pieces |
|---|---|
|
|
1/4 in |
|
|
Hex |
|
|
0° and 30° |
|
|
2,000 in-lbs |
|
|
Heat treated steel |
|
|
Yes |
|
|
0.485 lbs |
Compatibility
Built For
Pro Tip
Use the 0 degree position to start the fastener square, then switch to 30 degrees only when clearance becomes the problem. That gives you cleaner engagement on the screw head and helps the magnetic tip do its job.
Warranty & Support
Tool Nut's Take
Milwaukee 48-32-2301 SHOCKWAVE 30° KNUCKLE Pivoting Bit Holder is a smart add-on for awkward fastening
This is the kind of accessory you do not think about until a straight driver will not fit, and then it becomes the one you keep close.
- Who it's for: Pros and serious DIY users who run an impact driver in cabinets, corners, service spaces, and other cramped areas.
- Why it stands out: The locking 0 degree and 30 degree positions, impact-rated build, and magnetic tip make it more useful than a basic extension.
- Worth knowing: This is an access solution, not a universal replacement for straight driving. Use it when space is the issue and it pays for itself fast.
Common Questions
- Does this holder lock at more than one angle? Yes. It locks at 0 degrees for straight driving and 30 degrees for tight-space access.
- Is it impact rated? Yes. It is built as a SHOCKWAVE Impact Duty accessory and is rated to 2,000 inch-pounds of torque.
- What size accessories does it use? It is designed for 1/4 inch hex accessories and has a 1/4 inch hex shank for quick-connect chucks.
- Does it have a magnetic tip? Yes. The tip is magnetic for better fastener retention.

Join over 1/2 million customers who have trusted Tool Nut and given us a 4.8+ star rating on Google. Celebrating over 30 years of building together, since 1994.
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

