Simpson Strong-Tie Strong-Drive WSVF SUBFLOOR Screw (Collated), #9 x 2-in. T25, Gray, 2000-Pack (WSVF2S)
Simpson Strong-Tie Strong-Drive WSVF SUBFLOOR Screw (Collated), #9 x 2-in. T25, Gray, 2000-Pack (WSVF2S)
Out of Stock - Available to Order - Usually ships in 3-5 days
Product Details
Product Details
Key Features
Overview
The Simpson Strong-Tie WSVF2S Strong-Drive WSVF SUBFLOOR Screw is a collated wood screw for the Quik Drive auto-feed system, sized at #9 x 2 in. and sold in a 2,000-count package. This is a collated subfloor screw designed for fastening wood subfloor and sheathing to wood framing. Model Number: WSVF2S. If you are laying down a lot of floor and want fewer squeaks, faster installation, and the ability to back screws out later if needed, this is the right kind of fastener.
What matters here is not just the size. Simpson reworked the point and thread pattern so the screw starts easier and needs up to 25% less driving torque in single-material LVL, with test data also showing up to 20% faster installation. On the job, that means less tool strain, less battery drain on cordless-compatible driving setups, and less wasted time when you are running long rows of subfloor screws.
The head design is doing real work too. The deep T25 6-lobe recessed ribbed head improves bit retention and helps reduce cam-out, which is exactly what you want when you are driving collated screws in repeated cycles. The rimmed flat head with nibs is built to countersink cleanly, so the subfloor lays down tight without proud fasteners creating problems for finish flooring later.
This screw uses a variable thread design with a high-low threaded point and a 2/3-threaded shank. That combination is aimed at pulling material together efficiently instead of just boring its way in. For subfloor work, that pull matters because it helps close the gap between the joist and the panel. That is the whole reason screws outperform nails in squeak-prone floor assemblies.
The WSVF2S is also practical when the job changes later. Unlike fasteners that are basically there for good, these WSVF screws can be backed out, which gives you a way back into floor cavities for repairs, additions, or inspection. Electricians, plumbers, remodelers, and service crews all appreciate that when a finished floor has to come back up in one section without turning the area into a demolition project.
System fit is important with collated fasteners, and this screw is made for Simpson Strong-Tie Quik Drive tools including the PRO200S, PRO250G2, PRO300S, and Project Pro systems. That makes it a good match for crews already running Quik Drive equipment and looking for a dedicated subfloor fastening screw instead of trying to force a general-purpose collated screw into the job.
The coating on this WSVF2S version is Quik Guard, and the packaging quantity is 2,000 screws per collated load package. For production framing and decking-style floor assembly work, that kind of pack size makes sense because you are buying for throughput, not for a one-room patch. This is a fastener for builders, framers, and remodelers who want repeatable results over a lot of square footage.
If you are using a Quik Drive setup for subfloor fastening, this screw earns its place by solving the three things that slow crews down: hard starts, bit slip, and callbacks for noisy floors. It is best for contractors who care more about install speed and floor performance than saving a few dollars on generic collated screws.
Fast Subfloor Installation with the Quik Drive System
This collated screw is built for production floor work. Paired with a Quik Drive auto-feed screw gun, it keeps the install moving without stopping to hand-load individual fasteners.
- Collated format designed for Simpson Strong-Tie Quik Drive tools
- Up to 20% faster installation based on Simpson test data
- 2,000-count packaging supports large subfloor runs
Starts Easier and Reduces Tool Strain
The redesigned tip and thread pattern are there to make driving smoother, especially over long sections of wood-to-wood fastening where tool fatigue adds up fast.
- Requires up to 25% less driving torque in single-material LVL
- Less torque means less wear on the driving tool
- Helps get more screws driven per battery charge on cordless-capable systems
Made to Pull Panels Down Tight
Subfloor screws need to do more than sink flush. They need to clamp the panel to the joist, stay engaged, and resist the little movements that turn into squeaks later.
- Variable thread design helps draw wood members together
- 2/3-threaded shank supports panel pull-down
- Holding power helps reduce joist-to-subfloor gaps that cause noisy floors
Key Specifications
| Screw Size | #9 |
|---|---|
| Length | 2 in. |
| Drive Type | T25 6-Lobe |
| Head Type | Rimmed Flat Head with Nibs |
| Shank Type | 2/3-Threaded Shank |
| Thread Type | Variable Thread Design |
| Point Type | High-Low Threaded Point |
| Packaging Quantity | 2000 |
Compatibility
Built For
Pro Tip
If you are chasing squeak-free floors, keep your screw lines centered on the joists and use the WSVF2S where the 2 in. length matches your panel and framing stack-up. The screw can be backed out later, so it is a smart choice anywhere you may need access under the floor down the road.
Tool Nut's Take
Simpson Strong-Tie WSVF2S Strong-Drive WSVF SUBFLOOR Screw Gets the Job Done Faster
This is the kind of collated subfloor screw that makes sense for crews who install a lot of floor and do not want callbacks for squeaks.
- Who it's for: Framers, builders, and remodelers using Simpson Quik Drive systems for subfloor and sheathing work.
- Why it stands out: Lower driving torque, faster install speed, secure T25 engagement, and strong panel pull-down are exactly what matter in production subfloor fastening.
- Worth knowing: This is a system-specific collated fastener, so make sure your Quik Drive model matches. If you are not running a compatible auto-feed driver, this is not the right screw for the job.
Common Questions
- What is the Simpson Strong-Tie WSVF2S Strong-Drive WSVF SUBFLOOR Screw used for? It is designed for fastening wood subfloor and sheathing to wood framing in Quik Drive auto-feed applications.
- What drive does this screw use? It uses a T25 6-lobe drive.
- Can these screws be removed later? Yes. Simpson states that WSVF screws can be easily backed out for future access to floor cavities.
- Which Quik Drive tools fit this model? The WSVF2S is listed as compatible with the PRO200S, PRO250G2, PRO300S, and Project Pro systems.

Join over 1/2 million customers who have trusted Tool Nut and given us a 4.8+ star rating on Google. Celebrating over 30 years of building together, since 1994.
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.


