The Jet 708595 JSG-96 Benchtop 6 inch x 48 inch Belt / 9 inch Disc Sander is a stationary combination sander built for accurate shaping, edge sanding, fitting, and finish prep in woodshops and small fabrication spaces. This is a belt and disc sander designed for bench-mounted sanding, squaring, and shaping workpieces with better control than most handheld sanding tools. Model Number: 708595. If you need one machine that can handle long edges on the belt and precise face work on the disc, this setup makes a lot of sense.

The main draw here is versatility without going to a full floor-standing machine. You get a 6 inch wide belt section for flattening edges, easing corners, and working longer stock, along with a 9 inch sanding disc for end grain cleanup, small part fitting, and angle work with the miter gauge. The 3/4 horsepower motor runs the belt at 2,258 feet per minute, which is enough speed for serious stock removal while still being controllable for fitting parts and refining shape.

JET backed this machine with the kind of construction that matters on a benchtop sander. The cast-iron disc table helps keep vibration down, which directly affects surface quality and control. The tables tilt up to 45 degrees, and the large work support lets you run the belt vertically, horizontally, or in between depending on the job. That flexibility is useful when you are sanding bevels, cleaning up outside curves, or supporting awkward workpieces that never sit right on a fixed setup.

There are also a few design details that show this machine was meant to be used, not just spec-sheeted. The rubber-coated drive drum is there to maintain belt grip under load, so the belt is less likely to slip when you lean into hardwood or heavier sanding passes. JET also uses a belt tracking adjustment with a locking setup to keep the belt running true. Add in the quick-release belt tension lever, and belt changes are faster and less annoying than they are on a lot of older combo sanders.

Dust control is another real advantage. The single 4 inch dust port collects from both the belt and the disc, which helps keep abrasive dust off the table, off the workpiece, and out of the air. Hinged access panels also make routine belt changes and maintenance easier. In a small shop, that matters because the cleaner the machine stays, the easier it is to keep cuts and sanding lines consistent.

In day-to-day use, this is a good fit for woodworking shops, cabinet work, furniture building, trim fitting, and serious hobby work where part accuracy matters. It is also useful for general shop tasks like deburring and shaping non-ferrous materials when used appropriately with the correct abrasive. At roughly 100 pounds, it is not light, but that weight works in your favor by helping the machine stay planted on the bench instead of walking around under load.

If you are stepping up from a light-duty benchtop sander, the Jet 708595 JSG-96 Benchtop 6 inch x 48 inch Belt / 9 inch Disc Sander gives you more table support, better tracking control, stronger dust collection, and a heavier base. If your work is mostly small parts, edges, miters, and fit-up, this is the type of machine that earns its bench space pretty quickly.

Jet 708595 JSG-96 Benchtop 6 inch x 48 inch Belt / 9 inch Disc Sander is a real shop machine

This is the kind of combo sander you buy when you are done messing around with light-duty bench tools that flex, vibrate, and eat time.

• Who it's for: Woodworkers, cabinet guys, furniture builders, and serious home shop users who need accurate sanding support for edges, miters, and part fitting.
• Why it stands out: The cast-iron table, 6 inch x 48 inch belt, 9 inch disc, tracking control, and proper 4 inch dust port make it feel more like scaled-down stationary shop equipment than a consumer-grade combo sander.
• Worth knowing: It weighs about 100 pounds, so plan a dedicated bench spot. That extra mass is a good thing once you start leaning on it.

• What type of sander is this? It is a benchtop combination belt and disc sander with a 6 inch x 48 inch belt and a 9 inch sanding disc.
• Does it support dust collection? Yes. It has a single 4 inch dust port designed to collect dust from both the belt and disc areas.
• Is the speed variable? No. The machine is listed as non-variable speed.
• Can the tables tilt for angle sanding? Yes. The tables tilt up to 45 degrees, and preset stops at 90 degrees and 45 degrees are provided.